ScholaFly

PH08-06 Physics Watch

Specific latent heat of fusion and of vaporisation

Watch on YouTube

In this lesson

Specific latent heat of fusion: how to calculate the energy needed for a change of state using energy = mass x specific latent heat. AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Particles and matter 6 of 10. More at https://scholafly.com

By the end: Calculate the energy needed for a change of state using energy = mass x specific latent heat, and tell a change of state from a temperature change on a heating graph.

What it covers

  1. 0:00 Intro: specific latent heat of fusion
  2. 0:34 Specific latent heat
  3. 2:18 Does the temperature change?
  4. 3:51 Specific latent heat of fusion: melting ice
  5. 4:33 The kettle in numbers
  6. 6:26 Heating graphs
  7. 8:28 Three stages
  8. 10:30 Specific latent heat of fusion: finding
  9. 13:28 Back to the kettle

Key words

About this video

Specific latent heat of fusion and of vaporisation | GCSE Physics | PH08-06

Specific latent heat of fusion: how to calculate the energy needed for a change of state using energy = mass x specific latent heat.
AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Particles and matter 6 of 10.
More at https://scholafly.com

Watch first: PH08-03 - https://youtu.be/iQvF82gGhBk, PH08-05 - https://youtu.be/vcgkPrpFhZM
Video code: PH08-06 (search "ScholaFly PH08-06")

#GCSEPhysics #ParticlesAndMatter

For teachers
This GCSE Physics lesson teaches specific latent heat of fusion and of vaporisation. By the end, students should be able to calculate the energy needed for a change of state using energy = mass x specific latent heat, and tell a change of state from a temperature change on a heating graph. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.

Exam board specification references:
AQA 8463
- 4.3.2.3
Edexcel 1PH0
- 14.6
- 14.7
- 14.9
OCR J249
- P1.2d
- P1.2f
- PM1.2ii

Read the transcript

A splash of boiling water and a puff of steam from the same kettle are both at a hundred degrees Celsius. Which one burns skin worse? Same water, same temperature, so the tempting answer is that they do the same damage. The steam burns far worse, and no thermometer can show you why. Working out why takes one new idea, and then the steam can be counted in joules.

When a substance changes state, its temperature holds steady while the energy goes into the potential store of its particles. Specific latent heat is the energy needed to change the state of one kilogram of a substance with no change in temperature. Latent means hidden, because a thermometer shows no sign of this energy going in. Solid to liquid, or liquid back to solid, uses the specific latent heat of fusion. Fusion is an old word for melting. Liquid to gas, or gas back to liquid, uses the specific latent heat of vaporisation. Pick between them by the two states in the question. Solid and liquid means fusion, and liquid and gas means vaporisation. The energy for a change of state equals mass times specific latent heat, written E equals m L. Energy, E, is in joules. Mass, m, is in kilograms. Specific latent heat, L, is in joules per kilogram, with no degrees in it, because the temperature does not change. This equation is printed on the equation sheet. Its rearrangements each get their own line: L equals E over m, and m equals E over L. The same energy comes back out when the change runs backwards, because condensing and freezing transfer that energy to the surroundings.

With two heating equations now, one question picks between them: does the temperature change? If it does, use specific heat capacity, delta E equals m c delta theta. If it does not, the state is changing, so use E equals m L. One examiner's report, on a Higher paper, says many students mixed up specific heat capacity and specific latent heat, and read the wrong parts of the graph. The fix is to ask that one question out loud before you write any equation. Water at a hundred degrees Celsius is turned into steam at a hundred degrees. Which equation finds the energy: m c delta theta, m L with fusion, or m L with vaporisation? The m L with vaporisation. The temperature stays at a hundred, so the state is changing, and liquid to gas means vaporisation. Now the why. Why is m c delta theta wrong for that one? Because delta theta is nought. With no change in temperature, that equation would give no energy at all, when plenty is going in.

How much energy melts nought point two five kilograms of ice that is already at nought degrees Celsius? The specific latent heat of fusion of ice is three hundred and thirty-four thousand joules per kilogram. Check the stage first. The ice is already at its melting point, so this is a change of state only, with no temperature change. E equals m L, so E equals nought point two five kilograms times three hundred and thirty-four thousand joules per kilogram. That is eighty-three thousand five hundred joules, about eighty-four kilojoules.

Now the kettle. Five grams of steam at a hundred degrees Celsius condenses on skin into water at a hundred degrees. The specific latent heat of vaporisation of water is two million, two hundred and sixty thousand joules per kilogram. Convert before anything else. Five grams is nought point nought nought five oh kilograms. Condensing is a change of state, so E equals m L. Nought point nought nought five times two million, two hundred and sixty thousand is eleven thousand three hundred joules. Compare five grams of boiling water that cools on skin from a hundred to thirty-seven. No state changes there, so it takes the specific heat capacity equation, with c of four thousand two hundred. Find the change in temperature first, in degrees. How much energy does that cooling water give the skin? The change in temperature is a hundred minus thirty-seven, which is sixty-three degrees. Delta E is nought point nought nought five times four thousand two hundred times sixty-three, which is one thousand three hundred and twenty-three joules. The condensing steam hands over about eight and a half times as much, and that is before it even starts to cool. A report on a different Higher paper says very many students saw that a specific latent heat was very much more than the specific heat capacity of the same material. Seeing that gap puts you with them.

A heating graph plots temperature against time while energy goes in at a steady rate. A sloping section means the temperature is changing, so that stretch belongs to specific heat capacity. A flat section has a gradient of zero, so the temperature is not changing, so the state is changing. That stretch belongs to latent heat. The lower flat section sits at the melting point, and the higher one sits at the boiling point. The examiner for an older Higher paper notes that fewer students linked the melting and boiling points to the parts of the graph where the gradient was zero. The habit is to say the chain each time: gradient zero, so no temperature change, so the state is changing. A cooling curve runs the other way. Energy is leaving the material, and its flat sections are condensing or freezing, with energy transferred to the surroundings. The report that praised the latent heat comparison also records a surprisingly large number describing a cooling wax as if it were being heated from a solid into a liquid. The fix is to decide the direction of the energy, into the material or out of it, before reading anything off the graph. On a cooling curve for wax, the line falls, goes flat at fifty-four degrees Celsius, then falls again. Now a fresh graph. What is happening to the wax during that flat section? The wax is freezing at its melting point, and energy is leaving it to the surroundings at a steady temperature.

Some journeys need both equations, one stage at a time. Nought point two oh kilograms of ice comes out of a freezer at minus eighteen degrees Celsius and ends up as water at twenty-five. Ice has a c of two thousand one hundred, water has a c of four thousand two hundred, and the latent heat of fusion is three hundred and thirty-four thousand joules per kilogram. Sketch the heating graph first. It has a slope for the ice warming, a flat section for melting, and a slope for the water warming, with one equation for each section. Try the three stages on paper before I show you the answer. Stage one warms the ice from minus eighteen to nought, a change of eighteen degrees. Nought point two times two thousand one hundred times eighteen is seven thousand five hundred and sixty joules. Stage two melts the ice at nought degrees. Nought point two times three hundred and thirty-four thousand is sixty-six thousand eight hundred joules. Stage three warms the water from nought to twenty-five. Nought point two times four thousand two hundred times twenty-five is twenty-one thousand joules. Adding all three gives ninety-five thousand three hundred and sixty joules, about ninety-five kilojoules. The melting stage is the biggest of the three by a long way. In a report on a Higher multiple choice question like this, the examiner writes that a common wrong answer had not allowed for the energy needed to change state. The fix is to number the sections of the graph before any arithmetic, and give each section its own equation.

Last, a sixty watt heater sits in solid wax at its melting point. The wax stays at fifty-four degrees Celsius for six point oh minutes, while nought point one two kilograms of it melts. The energy comes from power times time, because power is the energy transferred each second. Six minutes is three hundred and sixty seconds, and sixty watts times three hundred and sixty seconds is twenty-one thousand six hundred joules. Now the part that is yours. What is the wax's specific latent heat? Rearrange the equation so that L equals E divided by m. Twenty-one thousand six hundred joules divided by nought point one two kilograms is a hundred and eighty thousand joules per kilogram. That steady fifty-four degrees is a flat section described in words, which makes it the wax's melting point. The Higher report on the mix-up of the two ideas adds that unit conversions were often done wrongly, and few students gave the unit, even with the equation printed on the sheet. The habit is a convert line for every gram or minute before anything is substituted, and joules per kilogram written in the answer line before the number goes in.

Four questions to close, each on the test that picks the equation. First, what does specific latent heat mean? Specific latent heat is the energy to change the state of one kilogram with no change in temperature. Now some new numbers. How much energy boils away half a kilogram of water already at a hundred degrees? Nought point five times two million, two hundred and sixty thousand is one million, one hundred and thirty thousand joules of energy. Now a graph question. What does a flat section on a heating graph tell you? A flat section has a gradient of zero, so the temperature is steady and the state is changing. Now a new material. Melting iron needs which latent heat, fusion or vaporisation? Melting iron takes fusion, because solid and liquid are the two states.

And the kettle. The steam burns worse than the splash at the same hundred degrees, because condensing steam hands your skin its latent heat, about eight and a half times what the cooling water gives.

If you can pick the right equation every time and add up the stages, give this a thumbs-up, because you're solid on this. If not, leave it un-thumbed, and come back to it later in the week.

Next in the chapter is Gas particles, temperature and pressure. Hopefully that's next in your feed, but if not, search for ScholaFly P H oh eight, oh seven.

Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.

Related terms

For: AQA GCSE 8463, Edexcel GCSE 1PH0, OCR GCSE J249

On the specification

BoardSpecStatement
AQA GCSE 84634.3.2.3Changes of state and specific latent heat
Edexcel GCSE 1PH014.6Explain how heating a system will change the energy stored within the system and raise its temperature or produce changes of state
Edexcel GCSE 1PH014.7Define the terms specific heat capacity and specific latent heat and explain the differences between them
Edexcel GCSE 1PH014.9Use the equation: thermal energy for a change of state (joule , J) = mass (kilogram, kg) × specific latent heat (joule per kilogram, J/kg)
OCR GCSE J249P1.2dDefine the term specific heat capacity and distinguish between it and the term specific latent heat
OCR GCSE J249P1.2fApply the relationship between specific latent heat and mass to calculate the energy change involved in a change of state
OCR GCSE J249PM1.2iiApply: thermal energy for a change in state (J) = mass (kg) × specific latent heat (J/kg)
For teachers

This GCSE Physics lesson teaches specific latent heat of fusion and of vaporisation. By the end, students should be able to calculate the energy needed for a change of state using energy = mass x specific latent heat, and tell a change of state from a temperature change on a heating graph. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.