ScholaFly

PH06-03 Physics Watch

Efficiency

Watch on YouTube

In this lesson

Efficiency: how to calculate the efficiency of an energy transfer as a decimal or a percentage. AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 3 of 6. Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70 More at https://scholafly.com

What it covers

  1. 0:00 Intro: efficiency
  2. 0:39 What efficiency
  3. 2:34 Scoring the filament bulb
  4. 4:32 A petrol lawnmower
  5. 7:11 A pump on a roof
  6. 10:37 An electric drill
  7. 11:44 Check the method

Key words

About this video

Efficiency | GCSE Physics | PH06-03

Efficiency: how to calculate the efficiency of an energy transfer as a decimal or a percentage.
AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 3 of 6.
Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70
More at https://scholafly.com

Watch first: PH05-04 - https://youtu.be/lHFCfiVP1S0, PH06-01 - https://youtu.be/EafgW1D6WIE
Video code: PH06-03 (search "ScholaFly PH06-03")

#GCSEPhysics #EfficiencyAndResources #Efficiency

For teachers
This GCSE Physics lesson teaches efficiency. By the end, students should be able to calculate the efficiency of an energy transfer as a decimal or a percentage. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.

Exam board specification references:
AQA 8463
- 4.1.2.2a
Edexcel 1PH0
- 3.11
- 8.15
OCR J249
- P7.2d
- PM7.2i

Read the transcript

An old filament bulb rated sixty watts and an LED rated eight watts can light a room equally brightly. So where does the old bulb's extra energy go? The old bulb takes in seven and a half times as much energy every second, for the same light. It is tempting to think the bigger number makes the better bulb. But how do you give each bulb one number that says how well it does its job? Both bulbs get that number, worked out in full, before the end.

Every device takes in energy and transfers some of it usefully. The rest is wasted, which means dissipated into the surroundings. Efficiency is the useful output energy transfer divided by the total input energy transfer. Both energies are measured in joules. The top of that fraction is what you wanted from the device. The bottom is everything you put in. Joules divided by joules cancel out, so efficiency has no unit. It is a decimal between nought and one, and multiplying it by a hundred turns it into a percentage. Now a quick one. Could nought point six, six joules or one point six be an efficiency? Only nought point six. Six joules has a unit, and efficiency has none. One point six is bigger than one, and an efficiency never is. One examiner's report, on a Foundation paper, gives a figure for this equation. About ninety-four per cent of the students identified the correct equation for efficiency. If you know the equation already, that part is safe. Using it, and turning it round, is what the rest of this video practises. Power is the rate of energy transfer: the energy transferred each second, measured in watts. If both energies in the equation are divided by the same time, they become powers. So efficiency is also the useful power output divided by the total power input. It is the same share, taken one second at a time.

The filament bulb takes in sixty watts of power, and gives out three watts as light. The LED takes in eight watts, and gives out the same three watts of light. Every value here is a power, so we use the power form: efficiency equals useful power output divided by total power input. For the filament bulb, we substitute. Three watts divided by sixty watts is nought point nought five. Times a hundred, that is five per cent. Only five per cent of what the old bulb takes in comes out as light. The wasted power is sixty watts take away three watts, which is fifty-seven watts. That is where the extra energy goes: it heats the bulb and the room around it. Now the LED: eight watts in, three watts of light out. What is its efficiency? Three watts divided by eight watts is nought point three seven five. Times a hundred, that is thirty-seven point five per cent. The LED wastes eight watts take away three watts, which is five watts. In both bulbs the watts cancel, which is why the answers have no unit. So the two bulbs have their numbers. The filament bulb is five per cent efficient and the LED is thirty-seven point five per cent efficient, so for the same light, the LED is seven and a half times as efficient. The old bulb is the more powerful of the two, and the less efficient. Power says how fast a device transfers energy, and efficiency says what share of that energy is useful.

Sometimes a question gives you the wasted energy instead of the useful energy. In one minute, a petrol lawnmower engine is supplied with ninety thousand joules from the chemical store of its fuel. Seventy-two thousand joules of that is dissipated, heating the engine and the air, and as sound. Before any dividing, is either of those two numbers the useful output? Neither of them is. The bigger one is the total input, and the smaller one is the wasted share. The useful output is what is left over, so you subtract first. Useful output is the total input take away the wasted energy: ninety thousand joules minus seventy-two thousand joules, which is eighteen thousand joules. Now divide. Eighteen thousand joules over ninety thousand joules is nought point two, and times a hundred, the engine is twenty per cent efficient. One examiner's report, on a Foundation paper, shows one student's answer to a question like this. The student underlined the numbers, but could not show how to find the useful energy by taking away the energy that went to the surroundings. The habit is one question before every division: is this number the useful share? If it is not, subtract first. Every answer also gets one check. The useful output can never be bigger than the input, because energy cannot be created. That means an efficiency is never more than one, or a hundred per cent. One exam specification warns that learners believe all energy is transferred efficiently, but no real device does that, so every real efficiency is less than one. Now a different one. A motor takes in five hundred joules and transfers four hundred joules usefully. A student writes its efficiency as one point two five. What has the student done wrong to get one point two five? The division is upside down. The useful output belongs on top and the total input underneath, which gives nought point eight, or eighty per cent.

Sometimes the efficiency is given, and you need the input. A pump lifts water into a tank on a roof, and it is thirty-five per cent efficient. In one minute, the water gains two thousand one hundred joules in its gravitational store. The question wants the energy supplied to the pump in that minute, and the energy wasted. First, convert the percentage. Thirty-five per cent is thirty-five divided by a hundred, which is nought point three five. Why must it go in as nought point three five, and not as thirty-five? Because the equation treats efficiency as a decimal between nought and one. Thirty-five would claim the pump gives out thirty-five times what it takes in. Then write the equation, and substitute straight away, on its own line. Nought point three five equals two thousand one hundred joules over the total input. Substituting first means you rearrange with the numbers in front of you, and each move is one you can check. Now rearrange, on the next line. Multiply both sides by the total input, and divide both sides by nought point three five. Total input equals two thousand one hundred joules divided by nought point three five, which is six thousand joules. Wasted energy is six thousand joules take away two thousand one hundred joules, which is three thousand nine hundred joules. Check: two thousand one hundred over six thousand is nought point three five, which is between nought and one, and it matches. One examiner's report, on a Foundation paper, records many students doing both steps in one go, with a wrong rearrangement, and scoring nothing for it. It says students should be encouraged to substitute first, then rearrange. That is the fix: substitute on one line, then rearrange on the next. Now a different slip. Another student writes: total input equals nought point three five times two thousand one hundred joules, which is seven hundred and thirty-five joules. What does the check say about seven hundred and thirty-five joules? It fails. Less energy in than useful energy out would mean the pump creates energy, which is impossible. The student multiplied where the rearrangement needs a divide. A third student forgets to convert, and puts thirty-five straight in. That gives a total input of sixty joules, for two thousand one hundred joules out, and the same check catches it. If the useful output is the unknown instead, the rearranged line is a multiplication: useful output equals efficiency times total input.

The same steps work with powers. An electric drill is nought point eight efficient, and its useful power output is four hundred and eighty watts. The equation and the substitution are done for you: nought point eight equals four hundred and eighty watts over the total power input. Your step is the rearrangement, and then the wasted power. Use the same rearranging you saw for the pump, one line at a time. Pause it there and work it out for yourself. The rearranged step divides by the efficiency, as it did for the pump. Total power input equals four hundred and eighty watts divided by nought point eight, which is six hundred watts. Wasted power is six hundred watts minus four hundred and eighty watts, which is one hundred and twenty watts. Check: four hundred and eighty over six hundred is nought point eight.

A quick check on the method, and each answer comes after you have had a go. A kettle takes in two thousand joules, and one thousand eight hundred joules of that heat the water. What is the kettle's efficiency, as a percentage? The useful share over the total gives nought point nine, so the kettle is ninety per cent efficient. Here's another. A motor is twenty-five per cent efficient, and it is supplied with four hundred joules. How many joules does the motor transfer usefully? Convert to nought point two five, then multiply by the input. The useful output is a hundred joules. Now with no numbers. A student's efficiency comes out as one point four. What went wrong? The division is upside down, because an efficiency is never more than one. The useful output belongs on top. One more. A two thousand watt heater or a five hundred watt fan: which is more efficient? You cannot tell from those numbers. Power says how fast energy is transferred, and efficiency needs the useful output as well. And the two bulbs are scored. The LED beats the filament bulb on efficiency while taking in far less power, which is the whole difference between how fast and how well.

If you're solid on this now, give it a thumbs-up, and you will know it is one you can leave alone. If it felt fast, that's normal for this many steps, so save it and work the pump through again on paper.

Next in the chapter is Increasing efficiency, which is for the Higher tier. If you sit Foundation, go on to Energy resources and how we use them. Hopefully that's next in your feed, but if not, search for ScholaFly P H oh six, oh four.

Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.

Related terms

For: AQA GCSE 8463, Edexcel GCSE 1PH0, OCR GCSE J249

On the specification

BoardSpecStatement
AQA GCSE 84634.1.2.2aEfficiency
Edexcel GCSE 1PH03.11Recall and use the equation: device the plied sup energy total device the transferre energy useful efficiency =
Edexcel GCSE 1PH08.15Recall and use the equation: device the plied sup energy total device the transferre energy useful efficiency =
OCR GCSE J249P7.2dCalculate energy efficiency for any energy transfer
OCR GCSE J249PM7.2iRecall and apply: efficiency = input energy transfer(J) useful output energy transfer(J)
For teachers

This GCSE Physics lesson teaches efficiency. By the end, students should be able to calculate the efficiency of an energy transfer as a decimal or a percentage. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.