PH06-04 Physics Watch
Increasing efficiency (Higher)
In this lesson
Increasing efficiency: how to describe how reducing a wasted energy transfer increases the efficiency of an intended transfer. AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 4 of 6. Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70 More at https://scholafly.com
What it covers
- 0:00 Intro: increasing efficiency
- 0:39 Efficiency
- 3:01 The efficiency chain
- 5:47 The same job, less input
- 7:34 Wasted depends on the job
- 9:34 Test the chain
Key words
About this video
Increasing efficiency (Higher) | GCSE Physics | PH06-04
Increasing efficiency: how to describe how reducing a wasted energy transfer increases the efficiency of an intended transfer.
AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 4 of 6.
Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70
More at https://scholafly.com
Watch first: PH06-03 - https://youtu.be/XDMrsB3XBt4
Video code: PH06-04 (search "ScholaFly PH06-04")
#GCSEPhysics #EfficiencyAndResources #IncreasingEfficiency
For teachers
This GCSE Physics lesson teaches increasing efficiency (Higher). By the end, students should be able to describe how reducing a wasted energy transfer increases the efficiency of an intended transfer. It works through three worked examples and the mistakes examiners report.
Exam board specification references:
AQA 8463
- 4.1.2.2b
Edexcel 1PH0
- 3.12
OCR J249
- P7.2e
Read the transcript
Imagine two electric scooters with the same battery, the same rider and the same route. Why does one get twenty kilometres on a full charge, and the other twenty-five? Your first guess might be the battery. But the batteries are the same, so the energy going in is the same. So where are the first scooter's missing five kilometres going, and what would you change to win them back? Those five missing kilometres are somewhere inside the first scooter, and the numbers will find them.
This video is for the Higher tier only. If you sit Foundation, you can skip it, and nothing later in this chapter depends on it. Efficiency is the useful output divided by the total input: the share of what goes in that ends up useful. If that equation is new, the video on calculating efficiency covers it. Each scooter's battery supplies one million joules on a full charge. Scooter A is nought point six efficient, and scooter B is nought point seven five efficient. Before any sums, which scooter wastes more of its million joules, A or B? Scooter A wastes more. Its efficiency is lower, so a smaller share of the same input ends up useful. Every kilometre needs thirty thousand joules of useful energy, to work against friction and air resistance, the drag of the air. For scooter A, useful energy is the efficiency times the total input. Nought point six times one million joules is six hundred thousand joules. Each kilometre takes thirty thousand joules, and six hundred thousand divided by thirty thousand gives a range of twenty kilometres. Scooter B is yours to work out, with the same two steps. How far does scooter B go on one full charge? For scooter B, nought point seven five times one million joules is seven hundred and fifty thousand joules of useful energy. Divided by thirty thousand joules for each kilometre, that is twenty-five kilometres. The rest is wasted: scooter A dissipates four hundred thousand joules, and B dissipates two hundred and fifty thousand. A wastes one hundred and fifty thousand joules more, and at thirty thousand joules a kilometre, that is exactly the missing five kilometres.
To increase efficiency, you reduce the wasted energy, so that a bigger share of the same input ends up useful. The explanation is a chain, said one link at a time. It starts with the change that is made, and the wasted transfer it cuts. Less energy is then dissipated, so a bigger share of the input is useful, and the efficiency rises. A student's answer reads: it makes it more efficient, so less energy is lost. Which link is missing from that answer? It never names the wasted transfer that the change cuts, such as the work done against friction. Repeating the question's own word explains nothing. One examiner's report, on a question about making a transfer more efficient, records a common error. Students restated the question and wrote about efficiency, instead of addressing what changes, such as the energy loss. The fix is to name the wasted transfer you cut, every time, and follow the chain to the end. And write dissipated, never lost. Take scooter A's wheel bearings; how oiling cuts friction is in the video on reducing unwanted energy transfers. Lubricate the bearings, and less work is done against friction. Less energy is dissipated in the bearings and the air, so more of the million joules is useful, and the efficiency and the range both rise. Every change shrinks the wasted share, but never to zero. Every real transfer dissipates some energy, so efficiency climbs towards a hundred per cent and never reaches it. Each way of raising efficiency is tied to the transfer it cuts. Streamlining cuts the work done against air resistance. Thermal insulation cuts the energy leaving by heating, where that heating is unwanted. Lower-resistance wires in a motor heat up less, and a better design, such as an LED in place of a filament bulb, cuts the waste in one go. Now a lighting question. An LED replaces a filament bulb: which wasted transfer is cut? The LED wastes far less on warming itself and the room, so far more of what goes in comes out as light.
A higher efficiency can show up a second way. A factory replaces a conveyor belt motor that is nought point four efficient with one that is nought point eight efficient. The belt does the same useful job every hour: one point two megajoules, where a megajoule is a million joules. This time the useful output is fixed, so we rearrange for the input: total input equals useful output divided by efficiency. For the old motor, one point two megajoules divided by nought point four is three megajoules supplied. The old motor wastes three megajoules take away one point two megajoules, which is one point eight megajoules. The new motor is yours: the same job, with an efficiency of nought point eight. At nought point eight efficient, how much does the new motor need, and waste? One point two megajoules divided by nought point eight is one point five megajoules supplied. Take away the one point two megajoules that is useful, and only nought point three megajoules is wasted. The energy supplied halves, and the energy wasted falls to a sixth. It is the same job, for less input. Those are the two faces of a higher efficiency. The same input gives more useful output, as with the scooters, or the same useful output needs less input, as with the conveyor.
Whether a transfer is wasted depends on what the device is for. The warmth from a fan's motor is wasted, because a fan is meant to move air. In an electric heater, is the warming it causes wasted, or useful? It is useful. Heating the room is the heater's job, so the same warming that wastes energy in a fan is the useful output of a heater. Thermal insulation raises efficiency only where heating is unwanted. Insulating the walls of a kettle cuts the energy leaving the hot water by heating, so more of the input stays in the water. Now a bigger one. An electric fan gets warm when it runs, and its motor hums. A designer wants to make it more efficient. Suggest two ways, and explain each one as a full chain, from the change to the efficiency. Have a go at this one before I show you. One way is to lubricate the motor's bearings, and it goes like this. Less friction means less work done against friction, so less energy is dissipated in the motor and the air. More of the input goes to the kinetic store of the blades, so the efficiency rises. Another way is to wind the motor with lower-resistance wire. The current heats the wire less, so less energy is dissipated, a bigger share of the input is useful, and the efficiency rises. Each answer names the wasted transfer it cuts. Writing that the fan is more efficient, and stopping there, explains nothing.
Let's test the chain on cases this video has not shown, with you going first each time. A car maker gives a car a smoother, more streamlined shape. How does that raise the efficiency, one link at a time? Less work is done against air resistance, so less energy is dissipated in the air. A bigger share of the fuel's energy is useful, and the efficiency rises. Here's a different one. A motor's efficiency goes up, and it keeps doing the same useful job. What happens to the energy it must be supplied with? It falls, because less of the input is wasted, so less has to be supplied. Now with a reason. Can good lubrication ever make a motor a hundred per cent efficient? It cannot. Every real transfer dissipates some energy, so efficiency gets closer to a hundred per cent but never reaches it. One more. Is the heating from a toaster wasted, or useful? It is useful, because browning the bread by heating is the toaster's whole job. And the first scooter's five missing kilometres were never lost. They were one hundred and fifty thousand joules of extra waste, and cutting that waste is how you win them back.
If you own this one now, give it a thumbs-up, and you will know it never needs a second watch. If not, save it, and come back to it later in the week, when the chain will feel shorter.
Next in the chapter is Energy resources and how we use them. Hopefully that's next in your feed, but if not, search for ScholaFly P H oh six, oh five.
Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.
Related terms
For: AQA GCSE 8463, Edexcel GCSE 1PH0, OCR GCSE J249
On the specification
For teachers
This GCSE Physics lesson teaches increasing efficiency (Higher). By the end, students should be able to describe how reducing a wasted energy transfer increases the efficiency of an intended transfer. It works through three worked examples and the mistakes examiners report.