ScholaFly

PH06-02 Physics Watch

Reducing unwanted energy transfers

Watch on YouTube

In this lesson

Reducing energy transfers: how to explain how lubrication, thermal insulation and thicker walls reduce unwanted energy transfers. AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 2 of 6. Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70 More at https://scholafly.com

What it covers

  1. 0:00 Intro: reducing energy transfers
  2. 0:33 Unwanted energy transfers
  3. 1:55 Oiling a bike chain
  4. 3:13 Thermal conductivity
  5. 6:04 Walls of a building
  6. 8:27 Insulation on a cable

Key words

About this video

Reducing Energy Transfers: insulation and lubrication | GCSE Physics | PH06-02

Reducing energy transfers: how to explain how lubrication, thermal insulation and thicker walls reduce unwanted energy transfers.
AQA 8463, Edexcel 1PH0 and OCR J249 GCSE. Efficiency and resources 2 of 6.
Full Efficiency and resources playlist: https://www.youtube.com/playlist?list=PLEn6zSy_gE70
More at https://scholafly.com

Watch first: PH06-01 - https://youtu.be/EafgW1D6WIE
Video code: PH06-02 (search "ScholaFly PH06-02")

#GCSEPhysics #EfficiencyAndResources #ReducingEnergyTransfers

For teachers
This GCSE Physics lesson teaches reducing unwanted energy transfers. By the end, students should be able to explain how lubrication, thermal insulation and thicker walls reduce unwanted energy transfers. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.

Exam board specification references:
AQA 8463
- 4.1.2.1
Edexcel 1PH0
- 14.10
- 3.10
- 3.9
- 9.10
OCR J249
- P7.2f
- P7.2g

Read the transcript

How can one cool box keep your drinks cold on a hot beach, and keep a hot pie hot as well? It is the same box, with the same walls, doing two opposite jobs. If insulation kept the cold in, the pie would go cold. If it kept the heat in, the drinks would warm up. So how can one material do both jobs? We will cut through that cool box wall and see what it actually does.

An unwanted energy transfer is energy being dissipated where you would rather it was not. Dissipated energy is never destroyed; it spreads into the surroundings and is stored in less useful ways. Most unwanted transfers cannot be stopped completely. What you can do is slow them down, which means reducing their rate. The rate of energy transfer is the energy transferred each second. Try that on a pan of hot soup on the side, with a lid on it. Does the lid stop energy leaving the soup, or slow the rate it leaves? The lid slows the rate. The soup still cools in the end, only more slowly, and that is what reducing an unwanted transfer means. One examiner's report, on a Higher paper, notes something encouraging. Almost all of the students knew that a beaker of hot water needed insulation, or a lid, or both. If you knew that too, you are with almost everyone who sat it. This video adds the words that explain why it works: rate, thickness and thermal conductivity.

Moving parts that rub together waste energy through friction. Tom's bike chain is dry, and it squeaks every time he pedals. Work is done against friction where the links grip the toothed wheels, called sprockets. That warms the chain and the air a little, and some energy is carried away as sound. Tom oils the chain. Putting oil or grease between moving surfaces is called lubrication. Tom says oiling it makes the chain run smoother. That is true, but it says nothing about the energy. What does oiling the chain do, step by step, to the energy Tom wastes? The oil reduces the friction between the links and the sprockets. Less friction means less work is done against friction, so less energy is dissipated into the thermal store of the chain and the air. More of the energy Tom transfers by pedalling now ends up in the kinetic store of the bike.

Now the cool box. Its walls are made of expanded polystyrene, four centimetres thick, and on the beach the air outside is warmer than the ice inside. Energy is transferred by heating from a warmer place to a cooler one. So here, energy flows from the beach air, through the walls, into the box. How easily energy passes through a material by heating is called its thermal conductivity. A material with a high thermal conductivity lets energy through fast. A thermal insulator is a material with a low thermal conductivity. Polystyrene is a good thermal insulator, and comparing insulators is a required practical with a video of its own. Now back to the drinks on the beach, with three possible answers to choose from. Does the box keep the cold in, keep all energy out, or slow the energy coming in? It slows the energy coming in. Nothing called cold moves anywhere; only energy is transferred. Polystyrene's low thermal conductivity means a low rate of energy transfer through the walls, so the ice gains energy slowly and melts slowly. Turn it round for the pie. The pie is hotter than the air, so energy flows out of it, and the same walls slow that energy down on its way out. The box does one job both times. It slows the rate of energy transfer, whichever way the temperature difference is driving it. One examiner's report, on a Foundation paper, records this. Nearly half of the students thought that thermal insulation increases the rate of energy transfer, and many were confused about how conduction and insulation are related. The fix is to keep the two words paired. An insulator has a low conductivity, so the transfer through it is slow. Now a different question. Suppose the walls of the cool box were eight centimetres thick, instead of four. What would those thicker walls do to how long the ice lasts? Thicker walls lower the rate of energy transfer even further, because the energy has more insulating material to pass through. So the ice lasts longer still.

The same two ideas decide how fast a building cools. Thicker walls, and walls with a lower thermal conductivity, both give a lower rate of cooling. That is why many houses have foam in the gap between their two layers of brick, called cavity wall insulation, and a thick layer of fluffy material in the loft. Three garden sheds are heated to the same temperature, and then the heaters are switched off on a cold night. Shed P has pine walls ten millimetres thick, and shed Q has pine walls twenty millimetres thick. Shed R also has pine walls twenty millimetres thick, with a layer of mineral wool fixed inside. Mineral wool has a much lower thermal conductivity than pine. Put the sheds in order of how fast they cool, the quickest first, with a reason for each step. Have a go at this one before I show you. Shed P cools fastest. Its walls are the thinnest, so the rate of energy transfer through them is the highest. Shed Q comes next. It is the same wood, twice as thick, so the rate is lower. Now the last step. Shed R's pine walls are as thick as Q's, so why does R cool more slowly? Shed R has the mineral wool as well, and its low thermal conductivity cuts the rate of energy transfer to the cold air even further. R cools slowest, and the order is P, then Q, then R. One examiner's report, on a Higher paper, describes a question about a wall with cavity insulation. Most students wrote vaguely about heat being kept inside and the cold not being let in. The thickness of the wall was rarely mentioned, and nor was the low thermal conductivity of the material. Start every answer like this with the two factors: how thick the wall is, and how low its thermal conductivity is. Both lower the rate of energy transfer.

An electric cable has copper wires inside a coat of plastic, and that plastic is called insulation too. But it is electrical insulation, and it is there to stop electric shocks. When a current flows, the copper itself warms up, because the wire has resistance, which means it resists the current. That is where the energy is dissipated: inside the copper. An electrician has two cables of the same length. Cable X has thin copper wires inside very thick plastic, and cable Y has thick copper wires inside thinner plastic. A customer says: use cable X, because the thick plastic will stop the wires wasting energy. Is the customer right about the thick plastic and the energy? Keep your reason ready. The customer is wrong. The energy is dissipated in the wire's metal core, as a result of its resistance, and thicker plastic does not change how much the wire dissipates. At most, it slows that energy reaching the air. To waste less, choose cable Y, because its thicker copper has a lower resistance. Why that wastes less is explained in the Higher video on reducing unwanted transfer with low-resistance wires. One examiner's report, on a Higher paper, records many answers about the thickness of the insulation, as if it were thermal insulation to stop the wires losing energy. It adds that the energy wasted can only be lowered by reducing the resistance of the wires, which is the copper's resistance to the current. When a question asks about the energy a wire wastes, answer about the wire's resistance, never about its plastic.

Four questions to finish, and you answer each one before I give mine. A flask keeps soup hot for hours. What do its walls do to the rate of energy transfer? They lower the rate of energy transfer from the hot soup to the cooler air outside. The walls have a low thermal conductivity, so energy passes through them slowly. Now a door hinge. Why does oiling a squeaky hinge cut the energy it wastes? The oil reduces friction in the hinge, so less work is done against friction, and less energy is dissipated into the thermal store of the hinge and the air. Here's a choice. Does a high thermal conductivity mean fast transfer, or slow transfer? It means fast transfer. A thermal insulator is the opposite, with a low conductivity and a slow transfer. Now the cable. Would thicker plastic on a kettle cable cut what its wire wastes? It would not. The wire wastes energy because of its resistance, so only a lower resistance, from thicker copper, would cut it. And the cool box on the beach was never choosing a direction. For the drinks and for the pie, it does one job: it slows the rate of energy transfer.

If this one is in the bag, give it a thumbs-up, and you will know you can skip it from now on. If it is not there yet, save it, give it a day, and look again.

Next in the chapter is Calculating efficiency. Hopefully that's next in your feed, but if not, search for ScholaFly P H oh six, oh three.

Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.

Related terms

For: AQA GCSE 8463, Edexcel GCSE 1PH0, OCR GCSE J249

On the specification

BoardSpecStatement
AQA GCSE 84634.1.2.1Energy transfers in a system
Edexcel GCSE 1PH014.10Explain ways of reducing unwanted energy transfer through thermal insulation
Edexcel GCSE 1PH03.10Describe the effects of the thickness and thermal conductivity of the walls of a building on its rate of cooling qualitatively
Edexcel GCSE 1PH03.9Explain ways of reducing unwanted energy transfer including through lubrication, thermal insulation
Edexcel GCSE 1PH09.10Explain ways of reducing unwanted energy transfer through lubrication
OCR GCSE J249P7.2fExplain ways of reducing unwanted energy transfer lubrication and thermal insulation
OCR GCSE J249P7.2gDescribe how the rate of cooling of a building is affected by the thickness and thermal conductivity of its walls (qualitative only)
For teachers

This GCSE Physics lesson teaches reducing unwanted energy transfers. By the end, students should be able to explain how lubrication, thermal insulation and thicker walls reduce unwanted energy transfers. It works through four worked examples and the mistakes examiners report, and suits Foundation and Higher tier students.