DT10-02 Design and Technology Watch
Isometric drawing: crating, ellipses and working from dimensions
In this lesson
Isometric drawing: how to draw a product in isometric, with worked examples and the mistakes examiners report. AQA 8552, Cambridge 0445, Edexcel 1DT0, Eduqas C600QS and OCR J310 GCSE. Technical drawing 2 of 6. More at https://scholafly.com
By the end: Draw a product in isometric - verticals vertical, the other edges at 30 degrees, true lengths along those three directions - from given dimensions or views, using a crate, isometric grid paper or a 30 degree set square; sketch holes and round parts as ellipses in isometric squares; and name the drawing correctly.
What it covers
- 0:00 Intro: isometric drawing: crating
- 0:34 Isometric drawing: crating: which could you take a [ruler] to?
- 3:14 Crating the phone stand
- 6:46 A round cable hole on the [back face]
- 8:58 Which [name] is right?
- 10:16 Your turn: isometric drawing: crating
Key words
About this video
Isometric drawing: crating, ellipses and working from dimensions | GCSE Design & Tech | DT10-02
Isometric drawing: how to draw a product in isometric, with worked examples and the mistakes examiners report.
AQA 8552, Cambridge 0445, Edexcel 1DT0, Eduqas C600QS and OCR J310 GCSE. Technical drawing 2 of 6.
More at https://scholafly.com
Watch first: DT10-01 - https://youtu.be/kmx8p92g5ZQ
Video code: DT10-02 (search "ScholaFly DT10-02")
#GCSEDesignTech #TechnicalDrawing #IsometricDrawingCrating
For teachers
This GCSE Design & Tech lesson teaches isometric drawing: crating, ellipses and working from dimensions. By the end, students should be able to draw a product in isometric - verticals vertical, the other edges at 30 degrees, true lengths along those three directions - from given dimensions or views, using a crate, isometric grid paper or a 30 degree set square; sketch holes and round parts as ellipses in isometric squares; and name the drawing correctly. It works through three worked examples and the mistakes examiners report.
Exam board specification references:
AQA 8552
- 3.3.5
Edexcel 1DT0
- 1.17.1
Eduqas C600QS
- 2.2 core.8
OCR J310
- M4b
Cambridge 0445-2027
- 5 > Isometric > b1
Cambridge 0445-2028
- 1.3.1/b2
- 3.2.1/b2
Read the transcript
Could a joiner build a staircase from a photo of it? Photograph a straight flight of stairs from the bottom, and it looks real. Every step is the same height, yet in the photo the far steps come out shorter. Now picture a drawing of the same stairs where nothing shrinks at all. To your eye, it looks very slightly wrong. One of those two is the picture makers actually work from.
Any drawing of a solid object has to decide what happens to the edges that run away from you. Which picture could you take a ruler to: A, the photo, or B, the drawing? It is B, the drawing. Every edge in it is drawn at its true length, so a ruler on the drawing gives you the real size of every step. That drawing is called an isometric drawing. Isometric means equal measure, because lengths in all three directions are drawn true. It follows a short set of rules. Vertical edges stay vertical. The other edges run at thirty degrees to the horizontal, one set rising to the left and the other rising to the right. Edges that are parallel on the box stay parallel in the drawing, and every length along those three directions is drawn true, with no shrinking. That is why it looks slightly wrong. Your eye expects far edges to shrink, and isometric refuses, so that every length can be measured. Now test those rules. A student draws a box with its verticals vertical and its top edges at thirty degrees, but makes the back edges a little shorter than the front ones. Is that an isometric drawing, and which rule decides it? No. Isometric draws every length true, so shrinking anything breaks the rule. That shrinking is what a perspective drawing does, and perspective has its own video. There are two ways to draw isometric. On isometric grid paper, the printed lines already run vertical and at thirty degrees both ways. On plain paper, a ruler and a thirty degree set square do the same job, and a set square is a flat plastic triangle with fixed angles. Either way, you start from the lowest front corner and count or measure along those three directions only. One examiner's report on an isometric question notes it was answered quite well where students knew about or had used isometric grid paper before. A few practice drawings on the grid are time well spent.
The method for drawing any product in isometric is called crating. You draw a light box, the crate, at the product's overall width, depth and height, then cut away whatever is not there. The product is an acrylic phone stand, an L shape eighty millimetres wide. Its base is seventy millimetres deep and ten millimetres thick, and its back is ten millimetres thick and rises to a hundred millimetres overall. On this grid, one space along any line stands for ten millimetres. Step one is to mark the lowest front corner on a grid point. Step two is the crate. How many spaces along each thirty degree line, and how many up? Eighty millimetres of width is eight spaces along one thirty degree line. Seventy of depth is seven spaces along the other. A hundred of height is ten spaces up. Step three is the L profile, drawn on the crate's side face, the face that shows depth and height. Count it round. It runs seven spaces along the bottom, then one space up for the ten millimetre base. How many spaces back along the top of the base to the upright, and why? Six spaces. The base is seven spaces deep and the back takes one of them, and seven minus one is six. Then the outline goes up nine spaces to reach the full height of ten, across one space for the back's thickness, and down ten spaces to the bottom. Step four: from every corner of that profile, run a line eight spaces along the width direction. Joining their ends repeats the L on the far side. Step five: rub out the crate lines you did not use, then go over the outline boldly. Construction lines stay thin and light, and the final outline is firm. Before you call it finished, check two things. Every length is counted against its number, and every edge runs along one of the three directions. Now a question about measuring. A student measures the seventy millimetres of depth forwards from the face of the upright, instead of from the front end. What happens to the stand's depth, and by how much is it out? The base comes out one grid space too long, eighty rather than seventy, because the back's thickness gets added on top of the full depth. One examiner's report on an isometric question records that most students drew one side too long, because they measured from an edge already in the drawing rather than from the actual end of the product. The habit that prevents it is to start every length from the true end of the product, usually the lowest front corner, and run it only along the three directions.
Round features come next, starting with a round cable hole on the back face of the stand. Predict it: in isometric, is the hole A, a circle, B, an ellipse, or C, a diamond? It is B, an ellipse, which is a squashed circle. A dinner plate looks oval when you see it at an angle, and on an isometric drawing every surface is seen at an angle. The hole is twenty millimetres across. It is centred across the eighty millimetre width, and its centre is fifty millimetres up from the bottom. Find the centre first. Half of eighty is forty, which is four spaces along the width direction, and fifty up is five spaces up the vertical. Round that centre, draw an isometric square twenty millimetres each way. That is a square drawn on the face, so its sides follow the vertical and the thirty degree width line, ten millimetres either side of the centre. Mark the middle of each side, then sketch the ellipse so it touches all four middles. It curves tightly at the two narrow corners and gently at the two wide ones. A sliver of the hole's far edge, showing inside it, gives the hole its depth. Now say why. Why is a neat true circle wrong on this face? Because the face is drawn at an angle, so everything on it is seen at an angle too. A true circle would look like a disc stuck on the front rather than a hole through it. A cylinder, like a round leg, is two of these ellipses joined by two straight lines. This video sketches every ellipse inside its square by eye, and that is the level the drawing needs.
The last skill is naming an isometric drawing when you see one. Two students are shown the same picture of a toolbox and asked to name the drawing method. One writes a 3D drawing, and the other writes isometric drawing. Which name scores, and what on the drawing would make you sure? Isometric drawing is the right name. A 3D drawing is true but too vague, because a perspective drawing is 3D as well. You can be sure from three signs. Verticals are vertical, the other edges sit at thirty degrees, and parallel edges stay parallel instead of closing towards a point. One examiner's report on a question asking students to name a drawing technique says wrong answers often named some kind of 3D drawing, or a different kind of technical drawing, or students left it blank. Write the name in full, isometric drawing, every time the question asks what the method is.
Time to test yourself on isometric before you go.
At what angle to the horizontal do the non-vertical edges run? Thirty degrees to the horizontal, one set rising to the left and one rising to the right.
Now a box this video never drew. One grid space is ten millimetres, and the box is a hundred and twenty wide, forty deep and sixty tall, all in millimetres. How many spaces go along each of the three directions? Twelve spaces of width, four of depth and six up.
Now one about holes. Before you sketch an ellipse, what do you draw, and how big? An isometric square on that face, as wide as the hole's diameter, with the ellipse touching the middle of each side.
Now a check on measuring. Where does every length start from? From the true end of the product, usually the lowest front corner, and only along the three directions.
Now the last one. A drawing's parallel edges close towards a point. Is it isometric? No. In isometric, parallel edges stay parallel. Edges that close towards a point belong to perspective.
Back to the staircase. The photo looked real but could not be measured. The isometric drawing looks very slightly wrong, and it is the one a joiner could build from, because every edge on it is a true length.
If you could crate that stand on a grid without stopping the video, give it a thumbs up, because you could teach this one. If not, save it, give it a day and look again.
Next in the chapter is One-point and two-point perspective. Hopefully that's next in your feed, but if not, search for ScholaFly D T one oh, oh three.
Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.
Related terms
For: AQA GCSE 8552, Edexcel GCSE 1DT0, Eduqas GCSE C600QS, OCR GCSE J310, Cambridge GCSE 0445
On the specification
| Board | Spec | Statement |
|---|---|---|
| AQA GCSE 8552 | 3.3.5 | {'ref': None, 'text': 'freehand sketching, isometric and perspective'}; {'ref': None, 'text': '2D and 3D drawings'}; {'ref': None, 'text': 'system and schematic diagrams'}; {'ref': None, 'text': 'annotated drawings that explain detailed development or the conceptual stages of designing'}; {'ref': None, 'text': 'exploded diagrams to show constructional detail or assembly'}; {'ref': None, 'text': 'working drawings: 3rd angle orthographic, using conventions, dimensions and drawn to scale'}; {'ref': None, 'text': 'audio and visual recordings in support of aspects of designing: eg interviews with client or users'}; {'ref': None, 'text': 'mathematical modelling'}; {'ref': None, 'text': 'computer based tools'}; {'ref': None, 'text': 'modelling: working directly with materials and components, eg card modelling, producing a toile when designing garments, constructing a circuit using breadboard.'} |
| Edexcel GCSE 1DT0 | 1.17.1 | {'ref': '1.17.1a', 'text': 'freehand sketching (2D and/or 3D)'}; {'ref': '1.17.1b', 'text': 'annotated sketches'}; {'ref': '1.17.1c', 'text': 'cut and paste techniques'}; {'ref': '1.17.1d', 'text': 'digital photography/media'}; {'ref': '1.17.1e', 'text': '3D models'}; {'ref': '1.17.1f', 'text': 'isometric and oblique projection'}; {'ref': '1.17.1g', 'text': 'perspective drawing'}; {'ref': '1.17.1h', 'text': 'orthographic and exploded views'}; {'ref': '1.17.1i', 'text': 'assembly drawings'}; {'ref': '1.17.1j', 'text': 'system and schematic diagrams'}; {'ref': '1.17.1k', 'text': 'computer-aided design (CAD) and other specialist computer drawing programs.'} |
| Eduqas GCSE C600QS | 2.2 core.8 | {'ref': None, 'text': 'Formal and informal 2D and 3D drawing.'}; {'ref': None, 'text': 'System and schematic diagrams.'}; {'ref': None, 'text': 'Annotated sketches.'}; {'ref': None, 'text': 'Exploded diagrams.'}; {'ref': None, 'text': 'Models.'}; {'ref': None, 'text': 'Presentations.'}; {'ref': None, 'text': 'Written notes.'}; {'ref': None, 'text': 'Flow diagrams'}; {'ref': None, 'text': 'Working drawings.'}; {'ref': None, 'text': 'Schedules.'}; {'ref': None, 'text': 'Audio and visual recordings.'}; {'ref': None, 'text': 'Mathematical modelling.'}; {'ref': None, 'text': 'Computer-based tools.'} |
| OCR GCSE J310 | M4b | Representing 3D objects in 2D, including isometric drawings |
| Cambridge GCSE 0445 | missing | the plan names no spec point for this board |
For teachers
This GCSE Design & Tech lesson teaches isometric drawing: crating, ellipses and working from dimensions. By the end, students should be able to draw a product in isometric - verticals vertical, the other edges at 30 degrees, true lengths along those three directions - from given dimensions or views, using a crate, isometric grid paper or a 30 degree set square; sketch holes and round parts as ellipses in isometric squares; and name the drawing correctly. It works through three worked examples and the mistakes examiners report.