DT10-01 Design and Technology Watch
Visualising 3D forms and drawing them in 2D
In this lesson
Visualising 3D forms for GCSE Design & Tech, with worked examples and the mistakes examiners report. AQA 8552, Edexcel 1DT0, Eduqas C600QS and OCR J310 GCSE. Technical drawing 1 of 6. More at https://scholafly.com
By the end: See a solid object as flat views - from the front, from above and from the side - know which two of its three dimensions each view shows, match a 3D drawing to its views and back, and transfer given dimensions exactly into a 2D drawing or a full-size template.
What it covers
- 0:00 Intro: visualising 3D forms: in 2D
- 0:43 Visualising 3D forms: in 2D: three dimensions
- 3:17 A desk phone stand
- 7:52 Drawing to size
Key words
About this video
Visualising 3D forms and drawing them in 2D | GCSE Design & Tech | DT10-01
Visualising 3D forms for GCSE Design & Tech, with worked examples and the mistakes examiners report.
AQA 8552, Edexcel 1DT0, Eduqas C600QS and OCR J310 GCSE. Technical drawing 1 of 6.
More at https://scholafly.com
Video code: DT10-01 (search "ScholaFly DT10-01")
#GCSEDesignTech #TechnicalDrawing #Visualising3DFormsIn2D
For teachers
This GCSE Design & Tech lesson teaches visualising 3D forms and drawing them in 2D. By the end, students should be able to see a solid object as flat views - from the front, from above and from the side - know which two of its three dimensions each view shows, match a 3D drawing to its views and back, and transfer given dimensions exactly into a 2D drawing or a full-size template. It works through two worked examples and the mistakes examiners report.
Exam board specification references:
AQA 8552
- 7.1:4b
Edexcel 1DT0
- App1:4
- App1:4b
Eduqas C600QS
- App B maths 4b
OCR J310
- M4b
Read the transcript
Could one flat drawing tell a factory how thick to make a phone, a paperback or a shoebox? Put all three on a table and look straight down at them. You see three rectangles of nearly the same shape. Tip them onto their sides and they could not be more different. The phone is about eight millimetres thick, the paperback about twenty, and the shoebox about a hundred. So a careful drawing from above, however neat, says nothing about how thick any of them is. How a flat drawing gets round that is where this video starts.
A solid object has three dimensions, and a sheet of paper has only two. A dimension is a size measured in one direction. For a product, the three are width from side to side, depth from front to back, and height from bottom to top. Because paper is missing a direction, a drawing has to choose how to show a solid. It can show it pictorially, as one 3D-looking drawing with three faces in sight. Or it can show the solid as separate flat views. Every formal drawing in this chapter is one of those two ways. A view is the true shape you see when you look straight at one side of an object, so no edge slants away from you. There are three views to know. The front view looks straight at the front. The plan is the view from above. The side view looks straight at one side. Each view can show only two of the three dimensions. The front view shows width and height, because the depth runs straight away from your eye. Now picture the same product from above instead. Which two dimensions does the plan show, and which one does it lose? Width and depth. From above, the height points straight at your eye, so the plan loses it. The side view shows depth and height, and this time it is the width that disappears. That is why the three rectangles from above looked alike. The thickness of a phone lying flat is its height, the one size a plan cannot show. Picture the paperback lying flat, and a factory that needs to know how thick it is. Which view gives that size: A, the plan, B, the front view, or C, none? It is B, the front view. The book's thickness is its height, and the front view carries height. The plan shows only the cover's outline. A second view is what gives the thickness.
Now a real product: a desk phone stand shaped like a step. Its base is ninety millimetres wide, seventy millimetres deep and fifteen millimetres tall. An upright back, ninety millimetres wide and twelve millimetres thick, stands at the rear edge and rises to a hundred and ten millimetres. Start with the front view. Looking straight at the front, you see the whole width of ninety millimetres and the whole height of a hundred and ten. That makes the front view a rectangle, ninety millimetres wide and a hundred and ten tall. One line runs across it fifteen millimetres up, and that line is the top edge of the base. The plan is yours to work out from those same sizes. What shape is the plan from above, and which two sizes does it carry? A rectangle ninety millimetres wide and seventy deep, so the plan carries width and depth. One line crosses it twelve millimetres in from the back edge. That line is where the top of the upright begins. The side view is where the step appears. It shows depth and height, so it carries the seventy and the hundred and ten. Walk round its outline. It goes seventy millimetres along the bottom, then up fifteen millimetres for the base. Along the top of the base to the upright: how long is that stretch? Fifty-eight millimetres. The base is seventy deep and the upright takes twelve of it, and seventy minus twelve is fifty-eight. From there the outline climbs to the full height of a hundred and ten millimetres, crosses the twelve millimetre thickness of the back, and drops straight down to the desk. That outline is an L shape, and only the side view shows the step as a step. No single view carried all three sizes. The front view held width and height, the plan held width and depth, and the side view held depth and height. One examiner's report on a question like this says most students gained some marks, especially for the basic L shape of the part, drawn the right way round. Seeing a side view in a 3D drawing is something you can already do, and counting each size is what makes it exact. Now a different question. Two students sketch the stand from above. Sketch A is a flat rectangle with one line across it. Sketch B shows the top of the stand with its front edges running off at an angle. Which sketch is the plan, and what gives the other away? Sketch A is the plan. Sketch B is a picture of the stand, because a view never shows an edge leaning away from you. One examiner's report on a question that asked for a plan records that some students drew a 3D picture of the product instead. The fix is a check before you finish. Look along every edge you drew, and if one leans away from you, you have drawn a picture rather than a view. Now one with a slope. A wedge doorstop is thin at the front and rises to its full height at the back. Which view shows the slope as one line: A, the front, B, the plan, or C, the side? It is C, the side view. From the side you look along the slope, so the sloping face shrinks to one line and the outline is a triangle. From the front or from above you look across the slope, so you see it as a face. How views like these are set out together on a formal drawing is the third angle orthographic projection video's job.
The second skill here is drawing a flat shape at its true size from the numbers you are given. Everything in this video is full size, so one millimetre on paper is one millimetre on the product. The product is a keyring tag cut from flat acrylic. It is a rectangle thirty millimetres wide and thirty millimetres tall, with a semicircle of radius fifteen millimetres on top. A hole six millimetres across goes through it, with its centre fifteen millimetres below the top of the curve. You draw it on squared paper where each square is five millimetres. The habit is to turn every size into squares before your pencil touches the paper. The width is thirty millimetres. Thirty divided by five is six, so the tag is six squares wide. Now the height. The rectangle is thirty millimetres tall, with the curve sitting on top of it. How many squares tall is the whole tag, curve included, and how many millimetres? Nine squares, which is forty-five millimetres. The straight sides take six squares and the curve's radius adds three. The hole is the last thing to place. Counting down from the top of the curve, where is the hole's centre, in squares? Fifteen millimetres is three squares. The curve tops out nine squares up, and three squares down from there is six squares up, in the middle, three squares in from each side. That point is also the semicircle's centre, the middle of the rectangle's top edge. One compass point does both jobs. Now the compass setting for the hole. Why is it three millimetres and not six? Because six millimetres is the hole's diameter, the distance right across it. A compass is set to the radius, which is half the diameter, so three millimetres. Now picture a second tag drawn by eye, seven squares wide instead of six. Side by side with the right one, it looks almost the same. Seven squares is thirty-five millimetres, which is five millimetres too wide. A tag cut from that drawing would not match the design. One examiner's report on a full-size template question records that many students drew the shape to the wrong width and lost a mark for it. The fix is a check you can see. Before you finish, read each number in the question, count its squares on your drawing, and tick it off.
Your turn to do the recalling now, one question at a time.
Which two dimensions does a side view show? Depth and height, because from the side the width runs straight away from you.
Now a box this video has not drawn: a shoebox three hundred and thirty millimetres wide, two hundred deep and a hundred and twenty tall. Which two of those sizes belong on its front view? Three hundred and thirty and a hundred and twenty. The front view shows width and height, so the depth is left for the plan and the side view.
Now count it: on five millimetre squares, how many squares is forty millimetres? Eight squares, because forty divided by five is eight.
Now the rule itself. In your own words, what makes a drawing a view rather than a picture? A view looks straight at one side of the object, so it shows a true shape and no edge slants away from you.
Now one for the compass. A hole is ten millimetres across. What is the compass set to? Five millimetres, because the compass takes the radius, half of the ten millimetre diameter.
Back to the phone, the paperback and the shoebox. From above they were three look-alike rectangles, but add a front view and their heights of eight, twenty and a hundred millimetres tell the factory how thick to make each one.
If those answers came without a pause, give this video a thumbs up, because this one's yours. If they did not, save it, draw the tag once on squared paper, and it comes with doing.
Next in the chapter is Isometric drawing: crating, ellipses and working from dimensions. Hopefully that's next in your feed, but if not, search for ScholaFly D T one oh, oh two.
Every other video is on scholafly.com too, easy to search by video code or by keyword. Whatever you're revising, go there and have a look, or, watch the next video.
Related terms
For: AQA GCSE 8552, Edexcel GCSE 1DT0, Eduqas GCSE C600QS, OCR GCSE J310
On the specification
| Board | Spec | Statement |
|---|---|---|
| AQA GCSE 8552 | 7.1:4b | Representing 2D and 3D forms |
| Edexcel GCSE 1DT0 | App1:4 | Angles in degrees |
| Edexcel GCSE 1DT0 | App1:4b | |
| Eduqas GCSE C600QS | App B maths 4b | Representing 2D and 3D forms |
| OCR GCSE J310 | M4b | Representing 3D objects in 2D, including isometric drawings |
For teachers
This GCSE Design & Tech lesson teaches visualising 3D forms and drawing them in 2D. By the end, students should be able to see a solid object as flat views - from the front, from above and from the side - know which two of its three dimensions each view shows, match a 3D drawing to its views and back, and transfer given dimensions exactly into a 2D drawing or a full-size template. It works through two worked examples and the mistakes examiners report.